smartctl voyait la température de ces deux disques avant que je change de disque racine, pourtant, maintenant, il ne les voie plus.
Comment est-ce possible ?
Avez-vous une solution ?
Merci.
Ignace.
pacman -Ss 's.m.a.r.t'
extra/hddtemp 0.3.beta15.53-3 [installé]
Gives you the temperature of your hard drive by reading S.M.A.R.T.
information
extra/libatasmart 0.19-5 [installé]
ATA S.M.A.R.T. Reading and Parsing Library
extra/plasma-disks 5.23.5-1 (plasma)
Monitors S.M.A.R.T. capable devices for imminent failure
extra/smartmontools 7.2-1 [installé]
Control and monitor S.M.A.R.T. enabled ATA and SCSI Hard Drives
11:49 [ignace@ignace-pc]~ $ sudo pacman -Ss 's.m.a.r.t'
[sudo] Mot de passe de ignace :
extra/hddtemp 0.3.beta15.53-3 [installé]
Gives you the temperature of your hard drive by reading S.M.A.R.T.
information
extra/libatasmart 0.19-5 [installé]
ATA S.M.A.R.T. Reading and Parsing Library
extra/plasma-disks 5.23.4-1 (plasma)
Monitors S.M.A.R.T. capable devices for imminent failure
extra/smartmontools 7.2-1 [installé]
Control and monitor S.M.A.R.T. enabled ATA and SCSI Hard Drives
12:06 [ignace@ignace-pc]~ $ sudo smartctl --all /dev/sdb
[sudo] Mot de passe de ignace :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 860 PRO 512GB
Serial Number: S42YNX0R900179V
LU WWN Device Id: 5 002538 e419000e0
Firmware Version: RVM02B6Q
User Capacity: 512 110 190 592 bytes [512 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Jan 22 12:06:41 2022 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 85) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 38
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 3
177 Wear_Leveling_Count 0x0013 100 100 000 Pre-fail Always - 0
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 070 062 000 Old_age Always - 30
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 099 099 000 Old_age Always - 1
235 POR_Recovery_Count 0x0012 100 100 000 Old_age Always - 0
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 69766794
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sudo smartctl --smart=on --offlineauto=on --saveauto=on /dev/sdX
12:19 [ignace@ignace-pc]~ $ sudo smartctl --smart=on --offlineauto=on --saveauto=on /dev/sdb
[sudo] Mot de passe de ignace :
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
SMART Attribute Autosave Enabled.
SMART Automatic Offline Testing Enabled every four hours.
12:19 [ignace@ignace-pc]~ $ sudo smartctl --smart=on --offlineauto=on --saveauto=on /dev/sdd
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.0-1-MANJARO] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
SMART Attribute Autosave Enabled.
SMART Automatic Timers not supported
SMART Enable Automatic Offline failed: scsi error badly formed scsi parameters
groups
?18:56 [ignace@ignace-pc]~ $ groups
sys network power nut lp wheel autologin ignace